Vacuum-gap-based lumped element Josephson parametric amplifier

We propose a lumped element Josephson parametric amplifier with vacuum-gap-based capacitor.The capacitor is made of quasi-floating aluminum pad and on-chip ground.We take a fabrication process compatible with air-bridge technology,which makes our design adaptable for future on-chip integrated quantum computing system.Further engineering the input impedance,we obtain a gain above 20 dB over 162-MHz bandwidth,along with a quasi quantum-limit noise performance.This work should facilitate the development of quantum information processing and integrated superconducting circuit design.     

甲烷浓度对碳化硅基底金刚石薄膜摩擦性能影响

利用热丝化学气相沉积法(HFCVD)在碳化硅基底上制备金刚石薄膜,采用场发射扫描电子显微镜、拉曼光谱仪、原子力显微镜研究了在不同甲烷浓度条件下制备的金刚石薄膜表面形貌及物相组成,在干摩擦条件下通过往复式摩擦磨损实验测试并计算了已制备金刚石薄膜的摩擦系数和磨损率,结合物相分析及摩擦磨损实验结果分析了甲烷浓度的改变对金刚石薄膜摩擦磨损性能的影响。结果表明,由于甲烷气体含量的升高,金刚石薄膜结晶质量下降,薄膜由微米晶向纳米晶转变。摩擦磨损实验结果显示:3%甲烷浓度条件下制备的金刚石薄膜耐磨性较好,磨损率为2.2×10^-7 mm³/mN;5%甲烷浓度条件下制备的金刚石薄膜摩擦系数最低(0.032),磨损率为5.7×10^-7 mm³/mN,制备的金刚石薄膜的耐磨损性能相比于碳化硅基底(磨损率为9.89×10^-5 mm³/mN)提升了两个数量级,显著提高了碳化硅基底的耐磨性。     

Eu:Lu2O3透明闪烁陶瓷的制备与性能

采用湿化学法合成了Eu原子掺量5%的Lu₂O₃陶瓷前驱体,通过SEM、XRD研究了煅烧前后前驱体和1 100 ℃煅烧4 h后粉体的形貌、结构以及物相。结果表明煅烧后的粉体为纳米类球形、高分散且结晶性良好的颗粒。颗粒尺寸为68.5 nm。使用煅烧后的粉体为原料,在1 650 ℃真空烧结30 h制备了高透过率的Eu:Lu₂O₃陶瓷,晶粒尺寸为46 μm,在611 nm处的直线透过率可以达到66.3%。此外对陶瓷的吸收曲线、光致激发和发射光谱特性以及X射线激发发射光谱进行研究。可观察到,Eu:Lu₂O₃陶瓷存在基质和激活离子两类吸收,光致发光光谱和X射线激发发射光谱均可以看出Eu:Lu₂O₃陶瓷存在极强的⁵D₀→⁷F₂跃迁发光,位于611 nm处。对比商业的BGO单晶的X射线发射光谱,可得本实验中制备的陶瓷的光输出为85 000 ph/MeV。Eu:Lu₂O₃陶瓷本身有着高X射线以及高能粒子的阻止能力,结合高光输出特性,表明Eu:Lu₂O₃陶瓷在X射线成像等领域具有巨大的潜在应用价值。     

Plasmon Coupling-Induced Hot Electrons for Photocatalytic Hydrogen Generation

We present the fabrication of core-shell-satellite Au@SiO₂-Pt nanostructures and demonstrate that LSPR excitation of the core Au nanoparticle can induce plasmon coupling effect to initiate photocatalytic hydrogen generation from decomposition of formic acid. Further studies suggest that the plasmon coupling effect induces a strong local electric field between the Au core and Pt nanoparticles on the SiO₂ shell, which enables creation of hot electrons on the non-plasmonic-active Pt nanoparticles to participate hydrogen evolution reaction on the Pt surface. In addition, small SiO₂ shell thickness is required in order to obtain a strong plamon coupling effect and achieve efficient photocatalytic activities for hydrogen generation.     

The unusual tribological behavior of diamond-like carbon films under high vacuum

We fabricate F-doped and F-S-codoped diamond-like carbon (DLC) films using plasma-enhanced chemical vapor deposition system. The hardness, Raman spectra, and high-vacuum tribological behaviors indicate that the films are DLC films. The hardness is close related to the tribological properties of DLC films under high vacuum. The high hardness of DLC films would be helpful for obtaining the long lifetime under high vacuum. The lifetimes of F-S-codoped DLC films are about 120 and 140 seconds, which is attributed to the fast graphitization under high vacuum. The lifetime of F-doped DLC films is prolonged to the value of around 300 and 440 seconds, X-ray photoelectron spectroscopy analysis exhibits the existence of the “adsorption” F, and transmission electron microscopy analysis shows that the “adsorption” F could react with Fe to form layered FeF₂ nanocrystal at the initial sliding, which could be helpful for prolonging the lifetime of F-doped DLC films under high vacuum. This investigation opens a new window to overcome the disadvantage of F, S-doped DLC films under high vacuum.     

中国聚变工程实验堆水冷包层钢构件流道成形控制研究

针对CFETR水冷包层流道钢构件热等静压制备时易变形压塌问题，利用单轴扩散焊设备开展了焊接工艺参数优化试验。在此基础上，重新设计了流道焊接界面位置和尺寸，用两步热等静压扩散焊法制备出了流道变形可控的平板型第一壁钢构件模块。优化试验表明，低活化钢试样的固相扩散焊温度需高于950℃，焊后经过760℃/60min回火热处理试样力学性能可以得到有效回复。     

(Gd,Lu)3Al5O12∶Tb3+,Eu3+透明陶瓷制备与发光性能

通过简单的化学沉淀法制备了纳米前驱体,结合真空烧结工艺,制备了一系列镥稳定钆铝石榴石{(Gd, Lu)₃Al₅O₁₂∶Tb,Eu}透明陶瓷。将透明陶瓷加工成1 mm厚的圆片,对透明陶瓷样品进行了X射线衍射、光致发光、透过率和衰减时间等表征。高温烧结过后,陶瓷样品仍保持稳定的石榴石相。选定313 nm作为透明陶瓷的激发波长,可获得最强的荧光发射。此外,通过对不同样品进行紫外可见荧光测试,获得了由绿光到红光的可调节发射。在313 nm激发,543 nm和591 nm的监测波长下,透明陶瓷样品均具有Eu³⁺的毫秒级衰减时间。